1、用光盘自带的Android目录下的已经编译好的kernel+android烧写启动正常。
2、我自己编译了光盘带的android-kernel-2.6.36-20120904这个内核，然后搭配光盘自带的rootfs_android-mlc2.ubi.烧写是正常success的。
但是，启动android之后，过了屏幕校正之后就不行了。
3、我以为是android的问题，于是我又折腾了半天编译出了光盘下的android-2.3.4-fs-20121011.tar。最终编译出了rootfs_android-mlc2.ubi。
搭配我自己编的kernel。问题依旧，现象一样。串口的输出如下，一直停在：
?equest_suspend_state: wakeup (3->0) at 89963962391 (2000-03-13 07:26:21.407360663 UTC)
init: untracked pid 1129 exited
init: untracked pid 1136 exited
4、用回光盘自带的已经编译好的kernel，一切都正常了。android启动OK。
感觉你们给出的源代码包是不是没验证过的啊，kernel是不是改得出了什么问题啊。。。郁闷死。
自带的编译好的kernel又不知道是哪个源码，估计也没在光盘里面。
搞得我的驱动一直insmod不进去。
串口输出完整如下：
?
Superboot6410
Ver: 120810
CPU: S3C6410 533MHz
RAM: 256MB
NAND: 2GB(MLC2) ID:ECD58472
Touch Device: 1-wire
LCD Type: S70(Auto)
蘒nstalling OS 'ANDROID'
Installing bootloader...
Coming to InstallSuperBoot
file: /images/superboot-6410.bin: 264 KB(270336 Byte)
蘒nstalling bootloader succeed
Installing kernel...
file: /images/Android/azImage: 3 MB(3751176 Byte)
蘒nstalling kernel succeed
蘒nstalling ubifs-image...
?ile: /images/Android/rootfs_android-mlc2.ubi: 91 MB(95420416 Byte)
?kip block 0x1b
Skip block 0x1c
蘒nstalling ubifs-image succeed
OS 'ANDROID' Installed
?
?
﨤oad Kernel...
?ncompressing Linux...?done, booting the kernel.
蘒nitializing cgroup subsys cpu
Linux version 2.6.36-FriendlyARM (root@vm) (gcc version 4.6.1 (Sourcery CodeBench Lite 2011.09-70) ) #1 PREEMPT Sun Mar 31 14:51:00 CST 2013
CPU: ARMv6-compatible processor [410fb766] revision 6 (ARMv7), cr=00c5387f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: MINI6410
MINI6410: S70 selected
Memory policy: ECC disabled, Data cache writeback
CPU S3C6410 (id 0x36410101)
S3C24XX Clocks, Copyright 2004 Simtec Electronics
camera: no parent clock specified
S3C64XX: PLL settings, A=532000000, M=266000000, E=84666666
S3C64XX: HCLK2=266000000, HCLK=133000000, PCLK=66500000
mout_apll: source is fout_apll (1), rate is 532000000
mout_epll: source is epll (1), rate is 84666666
mout_mpll: source is mpll (1), rate is 266000000
mmc_bus: source is mout_epll (0), rate is 84666666
mmc_bus: source is mout_epll (0), rate is 84666666
mmc_bus: source is mout_epll (0), rate is 84666666
usb-bus-host: source is clk_48m (0), rate is 48000000
uclk1: source is mout_epll (0), rate is 84666666
spi-bus: source is mout_epll (0), rate is 84666666
spi-bus: source is mout_epll (0), rate is 84666666
audio-bus: source is mout_epll (0), rate is 84666666
audio-bus: source is mout_epll (0), rate is 84666666
audio-bus: source is mout_epll (0), rate is 84666666
irda-bus: source is mout_epll (0), rate is 84666666
camera: no parent clock specified
s3c64xx: 6291456 bytes SDRAM reserved for fimc at 0x5f9f8000
s3c64xx: 8388608 bytes SDRAM reserved for pp at 0x5f1f8000
s3c64xx: 8388608 bytes SDRAM reserved for tv at 0x5e9f8000
s3c64xx: 2097152 bytes SDRAM reserved for jpeg at 0x5e7f8000
s3c64xx: 16777216 bytes SDRAM reserved for pmem at 0x5d7f8000
s3c64xx: 33554432 bytes SDRAM reserved for pmem_gpu1 at 0x5b7f8000
s3c64xx: 8388608 bytes SDRAM reserved for pmem_adsp at 0x5aff8000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Kernel command line: root=ubi0:FriendlyARM-root ubi.mtd=2 rootfstype=ubifs init=/linuxrc console=ttySAC0,115200 a?droidboot.console=s3c2410_serial0 lcd=S70
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 170068k/170068k available, 92076k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xff600000 - 0xffe00000 ( 8 MB)
vmalloc : 0xd0800000 - 0xe0000000 ( 248 MB)
lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.init : 0xc0008000 - 0xc0165000 (1396 kB)
.text : 0xc0165000 - 0xc0697000 (5320 kB)
.data : 0xc06c0000 - 0xc06fcfe0 ( 244 kB)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
RCU-based detection of stalled CPUs is disabled.
Verbose stalled-CPUs detection is disabled.
NR_IRQS:246
VIC @f4000000: id 0x00041192, vendor 0x41
VIC @f4010000: id 0x00041192, vendor 0x41
High resolution timer: rate = 66500000, HZ = 100
Console: colour dummy device 80x30
console [ttySAC0] enabled
Calibrating delay loop... ?30.84 BogoMIPS (lpj=2654208)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
Initializing cgroup subsys debug
Initializing cgroup subsys cpuacct
Initializing cgroup subsys freezer
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
?3c64xx_dma_init: Registering DMA channels
s3c64xx_dma_init1: registering DMA 0 (d0808100)
s3c64xx_dma_init1: registering DMA 1 (d0808120)
s3c64xx_dma_init1: registering DMA 2 (d0808140)
s3c64xx_dma_init1: registering DMA 3 (d0808160)
s3c64xx_dma_init1: registering DMA 4 (d0808180)
s3c64xx_dma_init1: registering DMA 5 (d08081a0)
s3c64xx_dma_init1: registering DMA 6 (d08081c0)
s3c64xx_dma_init1: registering DMA 7 (d08081e0)
PL080: IRQ 73, at d0808000
s3c64xx_dma_init1: registering DMA 8 (d080c100)
s3c64xx_dma_init1: registering DMA 9 (d080c120)
s3c64xx_dma_init1: registering DMA 10 (d080c140)
s3c64xx_dma_init1: registering DMA 11 (d080c160)
s3c64xx_dma_init1: registering DMA 12 (d080c180)
s3c64xx_dma_init1: registering DMA 13 (d080c1a0)
s3c64xx_dma_init1: registering DMA 14 (d080c1c0)
s3c64xx_dma_init1: registering DMA 15 (d080c1e0)
PL080: IRQ 74, at d080c000
S3C6410: Initialising architecture
?io: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
s3c-i2c s3c2440-i2c: slave address 0x10
s3c-i2c s3c2440-i2c: bus frequency set to 377 KHz
s3c-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
Advanced Linux Sound Architecture Driver Version 1.0.23.
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Switching to clocksource clock_source_timer2
﨨ET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
ashmem: initialized
squashfs: version 4.0 (2009/01/31) Phillip Lougher
io scheduler noop registered (default)
io scheduler cfq registered
S3C_LCD clock got enabled :: 133.000 Mhz
LCD TYPE :: Mini6410 will be initialized
Window[0] - FB1: map_video_memory: clear ff600000:00177000
FB1: map_video_memory: dma=5a000000 cpu=ff600000 size=00177000
Window[0] - FB2: map_video_memory: clear ff6bb800:000bb800
FB2: map_video_memory: dma=5a0bb800 cpu=ff6bb800 size=000bb800
﨏onsole: switching to colour frame buffer device 100x30
fb0: s3cfb frame buffer device
Window[1] - FB1: map_video_memory: clear ff800000:00177000
FB1: map_video_memory: dma=5a200000 cpu=ff800000 size=00177000
Window[1] - FB2: map_video_memory: clear ff8bb800:000bb800
FB2: map_video_memory: dma=5a2bb800 cpu=ff8bb800 size=000bb800
fb1: s3cfb frame buffer device
backlight initialized
leds initialized
pwm initialized
adc initialized
s3c6400-uart.0: s3c2410_serial0 at MMIO 0x7f005000 (irq = 16) is a S3C6400/10
s3c6400-uart.1: s3c2410_serial1 at MMIO 0x7f005400 (irq = 20) is a S3C6400/10
s3c6400-uart.2: s3c2410_serial2 at MMIO 0x7f005800 (irq = 24) is a S3C6400/10
s3c6400-uart.3: s3c2410_serial3 at MMIO 0x7f005c00 (irq = 28) is a S3C6400/10
loop: module loaded
pmem: 1 init
pmem_gpu1: 0 init
pmem_adsp: 0 init
S3C NAND Driver, (c) 2008 Samsung Electronics
MLC nand initialized, 2011 ported by FriendlyARM
S3C NAND Driver is using hardware ECC.
NAND device: Manufacturer ID: 0xec, Chip ID: 0xd5 (Samsung NAND 2GiB 3,3V 8-bit)
Creating 3 MTD partitions on "NAND 2GiB 3,3V 8-bit":
0x000000000000-0x000000400000 : "Bootloader"
0x000000400000-0x000000c00000 : "Kernel"
0x000000c00000-0x000080000000 : "File System"
?BI: attaching mtd2 to ubi0
UBI: physical eraseblock size: 1048576 bytes (102? KiB)
UBI: logical eraseblock size: 1032192 bytes
UBI: smallest flash I/O unit: 8192
UBI: VID header offset: 8192 (aligned 8192)
UBI: data offset: 16384
?BI: max. sequence number: 0
?BI: volume 0 ("FriendlyARM-root") re-sized from 89 to 2008 LEBs
UBI: attached mtd2 to ubi0
UBI: MTD device name: "File System"
UBI: MTD device size: 2036 MiB
UBI: number of good PEBs: 2032
UBI: number of bad PEBs: 4
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 2032
UBI: number of PEBs reserved for bad PEB handling: 20
UBI: max/mean erase counter: 1/0
UBI: image sequence number: 1140281026
UBI: background thread "ubi_bgt0d" started, PID 618
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
dm9000 Ethernet Driver, V1.31
?th0: dm9000a at d0930000,d0e00004 IRQ 108 MAC: 08:90:00:a0:90:90 (platform data)
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 79, io mem 0x74300000
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: S3C24XX OHCI
usb usb1: Manufacturer: Linux 2.6.36-FriendlyARM ohci_hcd
usb usb1: SerialNumber: s3c24xx
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
?sbserial: USB Serial Driver core
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
USB Serial support registered for aircable
usbcore: registered new interface driver aircable
USB Serial support registered for ark3116
usbcore: registered new interface driver ark3116
ark3116:v0.6:USB ARK3116 serial/IrDA driver
USB Serial support registered for Belkin / Peracom / GoHubs USB Serial Adapter
usbcore: registered new interface driver belkin
belkin_sa: v1.3:USB Belkin Serial converter driver
USB Serial support registered for ch341-uart
usbcore: registered new interface driver ch341
USB Serial support registered for cp210x
usbcore: registered new interface driver cp210x
cp210x: v0.09:Silicon Labs CP210x RS232 serial adaptor driver
USB Serial support registered for Reiner SCT Cyberjack USB card reader
usbcore: registered new interface driver cyberjack
cyberjack: v1.01 Matthias Bruestle
cyberjack: REINER SCT cyberJack pinpad/e-com USB Chipcard Reader Driver
USB Serial support registered for DeLorme Earthmate USB
USB Serial support registered for HID->COM RS232 Adapter
USB Serial support registered for Nokia CA-42 V2 Adapter
usbcore: registered new interface driver cypress
cypress_m8: v1.10:Cypress USB to Serial Driver
USB Serial support registered for debug
usbcore: registered new interface driver debug
USB Serial support registered for Digi 2 port USB adapter
USB Serial support registered for Digi 4 port USB adapter
usbcore: registered new interface driver digi_acceleport
digi_acceleport: v1.80.1.2:Digi AccelePort USB-2/USB-4 Serial Converter driver
USB Serial support registered for Edgeport 2 port adapter
USB Serial support registered for Edgeport 4 port adapter
USB Serial support registered for Edgeport 8 port adapter
USB Serial support registered for EPiC device
?sbcore: registered new interface driver io_edgeport
io_edgeport: v2.7:Edgeport USB Serial Driver
USB Serial support registered for Edgeport TI 1 port adapter
USB Serial support registered for Edgeport TI 2 port adapter
usbcore: registered new interface driver io_ti
io_ti: v0.7mode043006:Edgeport USB Serial Driver
USB Serial support registered for empeg
usbcore: registered new interface driver empeg
empeg: v1.3:USB Empeg Mark I/II Driver
USB Serial support registered for FTDI USB Serial Device
usbcore: registered new interface driver ftdi_sio
ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
USB Serial support registered for funsoft
usbcore: registered new interface driver funsoft
USB Serial support registered for Garmin GPS usb/tty
usbcore: registered new interface driver garmin_gps
garmin_gps: v0.33:garmin gps driver
USB Serial support registered for hp4X
usbcore: registered new interface driver hp4X
hp4x: v1.00:HP4x (48/49) Generic Serial driver
USB Serial support registered for PocketPC PDA
usbcore: registered new interface driver ipaq
ipaq: v1.0:USB PocketPC PDA driver
USB Serial support registered for IPWireless converter
usbcore: registered new interface driver ipwtty
usb 1-1: new full speed USB device using s3c2410-ohci and address 2
ipw: v0.4:IPWireless tty driver
USB Serial support registered for IR Dongle
usbcore: registered new interface driver ir-usb
ir_usb: v0.5:USB IR Dongle driver
USB Serial support registered for iuu_phoenix
usbcore: registered new interface driver iuu_phoenix
iuu_phoenix: v0.12:Infinity USB Unlimited Phoenix driver
USB Serial support registered for Keyspan - (without firmware)
USB Serial support registered for Keyspan 1 port adapter
USB Serial support registered for Keyspan 2 port adapter
USB Serial support registered for Keyspan 4 port adapter
usbcore: registered new interface driver keyspan
keyspan: v1.1.5:Keyspan USB to Serial Converter Driver
USB Serial support registered for Keyspan PDA
?SB Serial support registered for Keyspan PDA - (prerenumeration)
USB Serial support registered for Xircom / Entregra PGS - (prerenumeration)
usbcore: registered new interface driver keyspan_pda
keyspan_pda: v1.1:USB Keyspan PDA Converter driver
USB Serial support registered for KL5KUSB105D / PalmConnect
usbcore: registered new interface driver kl5kusb105d
kl5kusb105: v0.4:KLSI KL5KUSB105 chipset USB->Serial Converter driver
USB Serial support registered for KOBIL USB smart card terminal
usbcore: registered new interface driver kobil
kobil_sct: 21/05/2004:KOBIL USB Smart Card Terminal Driver (experimental)
USB Serial support registered for MCT U232
usbcore: registered new interface driver mct_u232
mct_u232: z2.1:Magic Control Technology USB-RS232 converter driver
USB Serial support registered for Moschip 2 port adapter
mos7720: 2.1:Moschip USB Serial Driver
usbcore: registered new interface driver moschip7720
USB Serial support registered for Moschip 7840/7820 USB Serial Driver
mos7840: 1.3.2:Moschip 7840/7820 USB Serial Driver
usbcore: registered new interface driver mos7840
USB Serial support registered for moto-modem
usbcore: registered new interface driver moto-modem
usb 1-1: New USB device found, idVendor=05e3, idProduct=0606
USB Serial support registered for navman
usbcore: registered new interface driver navman
usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1: Product: USB Hub 2.0
USB Serial support registered for ZyXEL - omni.net lcd plus usb
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usbcore: registered new interface driver omninet
omninet: v1.1:USB ZyXEL omni.net LCD PLUS Driver
USB Serial support registered for opticon
usbcore: registered new interface driver opticon
USB Serial support registered for oti6858
usbcore: registered new interface driver oti6858
USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
pl2303: Prolific PL2303 USB to serial adaptor driver
USB Serial support registered f?r qcaux
usbcore: registered new interface driver qcaux
USB Serial support registered for Qualcomm USB modem
usbcore: registered new interface driver qcserial
safe_serial: v0.1:USB Safe Encapsulated Serial
USB Serial support registered for safe_serial
usbcore: registered new interface driver safe_serial
USB Serial support registered for siemens_mpi
usbcore: registered new interface driver siemens_mpi
Driver for Siemens USB/MPI adapter
Version 0.1 09/26/2005 Thomas
Hergenhahn@web.de http://libnodave.sf.netUSB Serial support registered for Sierra USB modem
usbcore: registered new interface driver sierra
sierra: v.1.7.16:USB Driver for Sierra Wireless USB modems
USB Serial support registered for SPCP8x5
usbcore: registered new interface driver spcp8x5
spcp8x5: v0.10:SPCP8x5 USB to serial adaptor driver
USB Serial support registered for Quatech SSU-100 USB to Serial Driver
usbcore: registered new interface driver ssu100
ssu100: v0.1:Quatech SSU-100 USB to Serial Driver
USB Serial support registered for symbol
usbcore: registered new interface driver symbol
USB Serial support registered for TI USB 3410 1 port adapter
USB Serial support registered for TI USB 5052 2 port adapter
usbcore: registered new interface driver ti_usb_3410_5052
ti_usb_3410_5052: v0.10:TI USB 3410/5052 Serial Driver
USB Serial support registered for Handspring Visor / Palm OS
USB Serial support registered for Sony Clie 3.5
USB Serial support registered for Sony Clie 5.0
usbcore: registered new interface driver visor
visor: USB HandSpring Visor / Palm OS driver
USB Serial support registered for Connect Tech - WhiteHEAT - (prerenumeration)
USB Serial support registered for Connect Tech - WhiteHEAT
usbcore: registered new interface driver whiteheat
whiteheat: v2.0:USB ConnectTech WhiteHEAT driver
USB Serial support registered for vivopay-serial
usbcore: registered new interface driver vivopay-serial
vivopay_serial: v1.0:ViVOpay USB Serial Driver
USB Serial support registered for zio
usbcore: registered new int?rface driver zio
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
s3c-udc : S3C HS USB Device Controller Driver, (c) 2008-2009 Samsung Electronics
s3c-udc : version 15 March 2009 (DMA Mode)
android init
android_probe pdata: c06c6e18
android_bind
android_usb gadget: android_usb ready
f_adb init
android_register_function adb
f_mass_storage init
fsg_probe pdev: c06c6a38, pdata: c06c6da0
android_register_function usb_mass_storage
android_usb gadget: Mass Storage Function, version: 2009/09/11
android_usb gadget: Number of LUNs=1
lun0: LUN: removable file: (no medium)
adb_bind_config
mice: could not register psaux device, error: -16
mice: PS/2 mouse device common for all mice
input: gpio-keys as /devices/platform/gpio-keys/input/input0
touchscreen-1wire initialized
backlight-1wire initialized
input: TouchScreen Pipe as /devices/virtual/input/input1
ts-if initialized
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling
using rtc device, s3c, for alarms
s3c-rtc s3c64xx-rtc: rtc core: registered s3c as rtc0
i2c /dev entries driver
Linux video capture interface: v2.00
usbcore: registered new interface driver usbvision
USBVision USB Video Device Driver for Linux : 0.9.10
usbcore: registered new interface driver pvrusb2
pvrusb2: V4L in-tree version:Hauppauge WinTV-PVR-USB2 MPEG2 Encoder/Tuner
pvrusb2: Debug mask is 31 (0x1f)
usbcore: registered new interface driver zr364xx
zr364xx: Zoran 364xx
usbcore: registered new interface driver stkwebcam
gspca: main v2.10.0 registered
usbcore: registered new interface driver hdpvr
usbcore: registered new interface driver s2255
s3c-fimc: controller 0 registered successfully
s3c-fimc: controller 1 registered successfully
FIMC Driver, 2010 ported by FriendlyARM
http://www.arm9.netov965x: probe
s3c-fimc: i2c transfer error
s3c-fimc: i2c transfer error
s3c-fimc: i2c transfer error
s3c-fimc: i2c transfer error
s3c-fimc:?ov965x: Product ID fb:fb Manufacturer ID fb:fb
parent clock for camera: 266.000 MHz, divisor: 11
[CAM]RESET CAM.
?3C PostProcessor Driver v3.12, (c) 2009 Samsung Electronics
S3C6410 TV encoder Driver, (c) 2008 Samsung Electronics
?S3C6410 TV encoder Driver init OK.
S3C6410 TV scaler Driver, (c) 2008 Samsung Electronics
S3C6410 TV scaler Driver init OK.
S3C JPEG Driver, (c) 2007 Samsung Electronics
s3c-g2d: Driver loaded succesfully
s3c-g2d: Module initialized.
s3c_g3d: clock enabled
s3c-g3d: detected FIMG-3DSE version 1.5.0
s3c-g3d: Driver loaded succesfully
s3c-g3d: Module initialized.
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v0.1.0)
Bluetooth: HCI UART driver ver 2.2
Bluetooth: HCI H4 protocol initialized
Bluetooth: HCILL protocol initialized
Bluetooth: Generic Bluetooth USB driver ver 0.6
usbcore: registered new interface driver btusb
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
s3c-sdhci s3c-sdhci.0: clock source 0: hsmmc (133000000 Hz)
s3c-sdhci s3c-sdhci.0: clock source 1: hsmmc (133000000 Hz)
s3c-sdhci s3c-sdhci.0: clock source 2: mmc_bus (84666666 Hz)
mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA
s3c-sdhci s3c-sdhci.1: clock source 0: hsmmc (133000000 Hz)
s3c-sdhci s3c-sdhci.1: clock source 1: hsmmc (133000000 Hz)
s3c6400_setup_sdhci_cfg_card: CTRL 2=c0004120, 3=80808080
s3c-sdhci s3c-sdhci.1: clock source 2: mmc_bus (84666666 Hz)
mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
?ogger: created 64K log 'log_main'
logger: created 256K log 'log_events'
logger: created 64K log 'log_radio'
logger: created 64K log 'log_system'
asoc: AC97 HiFi <-> s3c-ac97 mapping ok
s3c6400_setup_sdhci_cfg_card: CTRL 2=c0004120, 3=00008080
mmc0: new high speed SDHC card at address e624
mmcblk0: mmc0:e624 SU08G 7.40 GiB
mmcblk0: p1
s3c6400_setup_sdhci_cfg_card: CTRL 2=c0004120, 3=80808080
嗀LSA device list:
#0: MINI6410 (WM9713)
TCP cubic registered
NET: Registered protocol family 17
Bluetooth: L2CAP ver 2.15
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 5
s3c-rtc s3c64xx-rtc: setting system clock to 2000-03-13 07:24:58 UTC (952932298)
Freeing init memory: 1396K
?BIFS: mounted UBI device 0, volume 0, name "FriendlyARM-root"
UBIFS: file system size: 2062319616 bytes (2013984 KiB, 1966 MiB, 1998 LEBs)
UBIFS: journal size: 12517376 bytes (12224 KiB, 11 MiB, 13 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
one_wire_status: 2
UBIFS: reserved for root: 0 bytes (0 KiB)
?Wire touchscreen OK
?ouchDevice: /dev/touchscreen-1wire
xres = 800, yres = 480
?ook 10 samples...
Top left : X = 3363 Y = 373
?ook 11 samples...
Top right : X = 3449 Y = 3729
?ook 11 samples...
Bot right : X = 531 Y = 3740
?ook 13 samples...
Bot left : X = 560 Y = 383
?ook 13 samples...
Center : X = 2014 Y = 2044
?29.840820 0.000776 0.208542
501.024017 -0.132767 0.001123
?nit: cannot open '/initlogo.rle'
?nit (1): /proc/1/oom_adj is deprecated, please use /proc/1/oom_score_adj instead.
?nabling adb
?db_open
? # [6n﨏ompat-wireless backport release: compat-wireless-2011-06-28-2-FA
Backport based on linux-next.git next-20110707
?fg80211: Calling CRDA to update world regulatory domain
?ibertas_sdio: Libertas SDIO driver
libertas_sdio: Copyright Pierre Ossman
?sbcore: registered new interface driver ath9k_htc
?sbcore: registered new interface driver rt73usb
?sbcore: registered new interface driver rt2800usb
?
rtw driver version=v3.0.1590.20110511
usbcore: registered new interface driver rtl8192cu
?sbcore: registered new interface driver zd1211rw
?a_cpu_pfn: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
FriendlyARM proprietary driver for mini6410 initialized.
?arning: `zygote' uses 32-bit capabilities (legacy support in use)
?equest_suspend_state: wakeup (3->0) at 89963962391 (2000-03-13 07:26:21.407360663 UTC)
init: untracked pid 1129 exited
init: untracked pid 1136 exited
?equest_suspend_state: wakeup (0->0) at 106516837654 (2000-03-13 07:26:37.960236016 UTC)
?nit: untracked pid 1235 exited
init: untracked pid 1236 exited
?equest_suspend_state: wakeup (0->0) at 122651098166 (2000-03-13 07:26:54.094496467 UTC)
init: untracked pid 1255 exited
init: untracked pid 1256 exited
?equest_suspend_state: wakeup (0->0) at 138599218000 (2000-03-13 07:27:10.042616031 UTC)
?nit: untracked pid 1275 exited
init: untracked pid 1276 exited
?equest_suspend_state: wakeup (0->0) at 154718889354 (2000-03-13 07:27:26.162287309 UTC)
init: untracked pid 1295 exited
init: untracked pid 1296 exited
?equest_suspend_state: wakeup (0->0) at 170979645850 (2000-03-13 07:27:42.423043489 UTC)
?nit: untracked pid 1315 exited
init: untracked pid 1316 exited
?
?
