不知版主有没有看过 韦东山 编的《嵌入式Linux应用开发完全手册》
当中第15章讲到u-boot 1.1.6的移植 其中修改后的／cpu/arm920t/s3c24x0/speed.c 如下所示
/*
* (C) Copyright 2001-2004
* Wolfgang Denk, DENX Software Engineering,
wd@denx.de.
*
* (C) Copyright 2002
* David Mueller, ELSOFT AG,
d.mueller@elsoft.ch *
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
/* This code should work for both the S3C2400 and the S3C2410
* as they seem to have the same PLL and clock machinery inside.
* The different address mapping is handled by the s3c24xx.h files below.
*/
#include <common.h>
#if defined(CONFIG_S3C2400) || defined (CONFIG_S3C2410) || defined (CONFIG_TRAB)
#if defined(CONFIG_S3C2400)
#include <s3c2400.h>
#elif defined(CONFIG_S3C2410)
#include <s3c2410.h>
#endif
DECLARE_GLOBAL_DATA_PTR;
#define MPLL 0
#define UPLL 1
/* ------------------------------------------------------------------------- */
/* NOTE: This describes the proper use of this file.
*
* CONFIG_SYS_CLK_FREQ should be defined as the input frequency of the PLL.
*
* get_FCLK(), get_HCLK(), get_PCLK() and get_UCLK() return the clock of
* the specified bus in HZ.
*/
/* ------------------------------------------------------------------------- */
static ulong get_PLLCLK(int pllreg)
{
S3C24X0_CLOCK_POWER * const clk_power = S3C24X0_GetBase_CLOCK_POWER();
ulong r, m, p, s;
if (pllreg == MPLL)
r = clk_power->MPLLCON;
else if (pllreg == UPLL)
r = clk_power->UPLLCON;
else
hang();
m = ((r & 0xFF000) >> 12) + 8;
p = ((r & 0x003F0) >> 4) + 2;
s = r & 0x3;
/* support both of S3C2410 and S3C2440, by
www.arm9.net */
if (gd->bd->bi_arch_number == MACH_TYPE_SMDK2410)
return((CONFIG_SYS_CLK_FREQ * m) / (p << s));
else
return((CONFIG_SYS_CLK_FREQ * m * 2) / (p << s)); /* S3C2440 */
}
/* return FCLK frequency */
ulong get_FCLK(void)
{
return(get_PLLCLK(MPLL));
}
/* for s3c2440 */
#define S3C2440_CLKDIVN_PDIVN (1<<0)
#define S3C2440_CLKDIVN_HDIVN_MASK (3<<1)
#define S3C2440_CLKDIVN_HDIVN_1 (0<<1)
#define S3C2440_CLKDIVN_HDIVN_2 (1<<1)
#define S3C2440_CLKDIVN_HDIVN_4_8 (2<<1)
#define S3C2440_CLKDIVN_HDIVN_3_6 (3<<1)
#define S3C2440_CLKDIVN_UCLK (1<<3)
#define S3C2440_CAMDIVN_CAMCLK_MASK (0xf<<0)
#define S3C2440_CAMDIVN_CAMCLK_SEL (1<<4)
#define S3C2440_CAMDIVN_HCLK3_HALF (1<<8)
#define S3C2440_CAMDIVN_HCLK4_HALF (1<<9)
#define S3C2440_CAMDIVN_DVSEN (1<<12)
/* return HCLK frequency */
ulong get_HCLK(void)
{
S3C24X0_CLOCK_POWER * const clk_power = S3C24X0_GetBase_CLOCK_POWER();
unsigned long clkdiv;
unsigned long camdiv;
int hdiv = 1;
/* support both of S3C2410 and S3C2440, by
www.arm9.net */
if (gd->bd->bi_arch_number == MACH_TYPE_SMDK2410)
return((clk_power->CLKDIVN & 0x2) ? get_FCLK()/2 : get_FCLK());
else
{
clkdiv = clk_power->CLKDIVN;
camdiv = clk_power->CAMDIVN;
/* work out clock scalings */
switch (clkdiv & S3C2440_CLKDIVN_HDIVN_MASK) {
case S3C2440_CLKDIVN_HDIVN_1:
hdiv = 1;
break;
case S3C2440_CLKDIVN_HDIVN_2:
hdiv = 2;
break;
case S3C2440_CLKDIVN_HDIVN_4_8:
hdiv = (camdiv & S3C2440_CAMDIVN_HCLK4_HALF) ? 8 : 4;
break;
case S3C2440_CLKDIVN_HDIVN_3_6:
hdiv = (camdiv & S3C2440_CAMDIVN_HCLK3_HALF) ? 6 : 3;
break;
}
return get_FCLK() / hdiv;
}
}
/* return PCLK frequency */
ulong get_PCLK(void)
{
S3C24X0_CLOCK_POWER * const clk_power = S3C24X0_GetBase_CLOCK_POWER();
unsigned long clkdiv;
unsigned long camdiv;
int hdiv = 1;
/* support both of S3C2410 and S3C2440, by
www.arm9.net */
if (gd->bd->bi_arch_number == MACH_TYPE_SMDK2410)
return((clk_power->CLKDIVN & 0x1) ? get_HCLK()/2 : get_HCLK());
else
{
clkdiv = clk_power->CLKDIVN;
camdiv = clk_power->CAMDIVN;
/* work out clock scalings */
switch (clkdiv & S3C2440_CLKDIVN_HDIVN_MASK) {
case S3C2440_CLKDIVN_HDIVN_1:
hdiv = 1;
break;
case S3C2440_CLKDIVN_HDIVN_2:
hdiv = 2;
break;
case S3C2440_CLKDIVN_HDIVN_4_8:
hdiv = (camdiv & S3C2440_CAMDIVN_HCLK4_HALF) ? 8 : 4;
break;
case S3C2440_CLKDIVN_HDIVN_3_6:
hdiv = (camdiv & S3C2440_CAMDIVN_HCLK3_HALF) ? 6 : 3;
break;
}
return get_FCLK() / hdiv / ((clkdiv & S3C2440_CLKDIVN_PDIVN)? 2:1);
}
}
/* return UCLK frequency */
ulong get_UCLK(void)
{
return(get_PLLCLK(UPLL));
}
#endif /* defined(CONFIG_S3C2400) || defined (CONFIG_S3C2410) || defined (CONFIG_TRAB) */
更改后编译出现错误
peed.c:1: warning: target CPU does not support interworking
speed.c: In function 'get_HCLK':
speed.c:114: error: 'S3C24X0_CLOCK_POWER' has no member named 'CAMDIVN'
speed.c: In function 'get_PCLK':
speed.c:154: error: 'S3C24X0_CLOCK_POWER' has no member named 'CAMDIVN'
make[1]: *** [speed.o] 错误 1
make[1]:正在离开目录 `/opt/FriendlyARM/QQ2440/u-boot-1.1.6/cpu/arm920t/s3c24x0'
make: *** [cpu/arm920t/s3c24x0/libs3c24x0.a] 错误 2
我看了你们做好移植以后的u-boot的代码，好像这个没有什么不同
可是就是编译不过
是不是我用的编译器有问题4.3.2 可是昨天用这个编译器编译你们移植好的u-boot没有问题！
求救
