感谢回复 前几天有事 昨天重弄了下 确实是SUPERBOOT没烧好 现在WINCE能启动了 但是触摸屏不好使 鼠标键盘也不能用 貌似USB驱动
NANDFLASH启动时串口的信息 屏是P43 镜像是光盘里给的 啥都没改过
Superboot-2451 V1.05a(20131223) by FriendlyARM
Booting from NAND
Reading...Launch Windows CE...
Windows CE Kernel for ARM (Thumb Enabled) Built on May 7 2012 at 12:47:43
INFO:OALLogSetZones: dpCurSettings.ulZoneMask: 0xb
DCache: 128 sets, 4 ways, 32 line size, 16384 size
ICache: 128 sets, 4 ways, 32 line size, 16384 size
FCLK:400000000, HCLK:133333333, PCLK:66666666
+OALArgsInit()
Arguments area is initialized
-OALArgsInit()
TCNTB4: 8234 8234
TCFG0 : 0
TCFG1 : 0
-OEMInit
[OAL]++OEMEnumExtensionDRAM
cMemSections = 15
[OAL] --OEMEnumExtensionDRAM
#### FMD_DRIVER:::FMD_INIT
(NAND ID:0xecda) --> OK.
NUM_OF_BLOCKS = 2048
PAGES_PER_BLOCK = 64
SECTORS_PER_PAGE = 4
#### FMD_DRIVER:::FMD_OEMIoControl
FMD_OEMIoControl: IOCTL_FMD_GET_INTERFACE
+++++FMD_GetInfo++++++
NUMBLOCKS : 1773(0x6ed), SECTORSPERBLOCK = 64(0x40), BYTESPERSECTOR = 2048(0x800)
+++++FMD_GetInfo++++++
NUMBLOCKS : 1773(0x6ed), SECTORSPERBLOCK = 64(0x40), BYTESPERSECTOR = 2048(0x800)
+++++FMD_GetInfo++++++
NUMBLOCKS : 1773(0x6ed), SECTORSPERBLOCK = 64(0x40), BYTESPERSECTOR = 2048(0x800)
#### FMD_DRIVER:::FMD_OEMIoControl
FMD_OEMIoControl: unrecognized IOCTL (0x71c24).
+++++FMD_GetInfo++++++
NUMBLOCKS : 1773(0x6ed), SECTORSPERBLOCK = 64(0x40), BYTESPERSECTOR = 2048(0x800)
OEM: Not cleaning system hive
OEM: Not cleaning user profiles
OEM: Not cleaning system hive
DEBUG: CreateSerialObject 3
DEBUG: CreateSerialObject 2
DEBUG: CreateSerialObject 1
DEBUG: CreateSerialObject 0
Audio Input IRQ(DMA1) mapping: [IRQ:41->sysIRQ:22].
Audio Output IRQ(DMA2) mapping: [IRQ:42->sysIRQ:23].
I2C_IST[2, 2]: ACK NOT received
I2C_IST[2, 1]: ACK NOT received
I2C_IST[2, 0]: ACK NOT received
+OALIoCtlHalGetHWEntropy
HOST CAP : 4
[DISP:INF] g_pLcdConReg = 0xd29e0000
[DISP:INF] g_pGPIOReg = 0xd2a00000
DM9K BANK Init.
[dm9: Chip signature is 90000A46
[dm9: Chip signature is 90000A46
[HSMMC1] Initializing the HSMMC Host Controller
[HSMMC1] Turn OFF the F/B delay control.
[HSMMC0] Initializing the HSMMC Host Controller
[HSMMC0] Turn OFF the F/B delay control.
[HSMMC0] Card is Removed!
[HSMMC1] Card is Inserted!
USB Serial Function Class Enabled : Serial_Class
+OALIoCtlHalGetDeviceInfo(...)
OALIoCtlHalGetDeviceInfo():SPI_GETUUID
-OALIoCtlHalGetDeviceInfo(SPI = SPI_GETUUID, rc = 1)
LED_Init
LED_Gpio_Setting
[HSMMC1] Turn OFF the F/B delay control.
[HSMMC1] Setting for 1 bit mode , Clock Rate = 100000 Hz
[HSMMC1] Turn OFF the F/B delay control.
ERR CMD:5 : If the card is not a SDIO, CMD 5 does not work in reason.
ERR CMD:1 : If the card is not a MMC, CMD 1 does not work in reason.
++OALIoCtlHalGetDispInfo()
--OALIoCtlHalGetDispInfo()
++OALIoCtlHalGetDispInfo()
--OALIoCtlHalGetDispInfo()
FriendlyARM got the LCD paramters, Name is P43
[DISP:INF] VCLK Source = LCDCLK from EPLL (96000000 Hz)
[DISP:INF] VCLKSrc = 96000000, VCLK = 9728420, Div = 9
[DISP:INF] VCLK Direction = Divided, Divider = 9, VCLK = 10666666 Hz
LDI_LTE480WV_RGB_port_initialize(): dont know why set GPB1
++OALIoCtlHalSetTimer3ISR()
--OALIoCtlHalSetTimer3ISR()
LCD type:19 VER:1127[HSMMC1] Setting for 4 bit mode , Clock Rate = 25000000 Hz
[HSMMC1] Turn OFF the F/B delay control.
I2C_IST[2, 1]: ACK NOT received
I2C_IST[2, 0]: ACK NOT received
I2CWrite ERROR: 1460
I2C_IST 是不是这个是管触摸的啊 出错了
