tiny210的板子，安卓2.3的系统
启动时，到Calibrating delay loop处不动了，
本来是好好的，烧写的系统也是光盘自带的，有了解的恳请指教一二，谢谢先。
下面是到停止时的部分截屏
[ 0.000000] Built 2 zonelists in Zone order, mobility grouping on. Total pag
es: 130048
[ 0.000000] Kernel command line: root=/dev/mtdblock4 console=ttySAC0,115200 i
nit=/linuxrc androidboot.console=s3c2410_serial0 lcd=H43
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 256MB 256MB = 512MB total
[ 0.000000] Memory: 345704k/345704k available, 178584k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xff000000 - 0xffe00000 ( 14 MB)
[ 0.000000] vmalloc : 0xe0800000 - 0xfc000000 ( 440 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .init : 0xc0008000 - 0xc016b000 (1420 kB)
[ 0.000000] .text : 0xc016b000 - 0xc072c000 (5892 kB)
[ 0.000000] .data : 0xc072c000 - 0xc086fa60 (1295 kB)
[ 0.000000] SLUB: Genslabs=9, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, No
des=4
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] Verbose stalled-CPUs detection is disabled.
[ 0.000000] NR_IRQS:393
[ 0.000000] VIC @fd000000: id 0x00041192, vendor 0x41
[ 0.000000] VIC @fd010000: id 0x00041192, vendor 0x41
[ 0.000000] VIC @fd020000: id 0x00041192, vendor 0x41
[ 0.000000] VIC @fd030000: id 0x00041192, vendor 0x41
[ 0.000000] mult[140737]
[ 0.000000] max_delta_ns[2937815369]
[ 0.000000] min_delta_ns[30517]
[ 0.000000] rate[32768]
[ 0.000000] HZ[256]
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [ttySAC0] enabled
[ 0.489792] Calibrating delay loop...
