210V2 独立输出分辨率依旧是720P调上去保存，重启无效

210V2 独立输出分辨率依旧是720P调上1080P去保存，重启无效 。用的是友善提供的linux+QT系统。请问怎么弄？
（不接LCD，重新使用minitools刷系统，如图）

而且qt系统的关机和重启都不正常，关机时系统halt了背光还在，led灯常亮。reboot也是，没正常关到或重启到机器

Please press Enter to activate this console. [   53.023503] usb 1-1.4: new low s
peed USB device number 4 using s5p-ehci
[   53.152290] input: OM as /devices/platform/s5p-ehci/usb1/1-1/1-1.4/1-1.4:1.0/
input/input4
[   53.162378] generic-usb 0003:04F3:0232.0003: input: USB HID v1.11 Mouse [OM]
on usb-s5p-ehci-1.4/input0
umount: can't remount none read-only
umount: none busy - remounted read-only
umount: none busy - remounted read-only
swapoff: /etc/fstab: No such file or directory
The system is going down NOW!
Sent SIGTERM to all processes
[24/Dec/2012:05:40:28 +0000] caught SIGTERM, starting shutdown
[24/Dec/2012:05:40:28 +0000] exiting Boa normally (uptime 384 seconds)
Sent SIGKILL to all processes
Requesting system halt
[  410.176634] System halted.

不要接LCD，可在论坛中搜“全屏显示”看详细说明

Board type: 2
NAND Low-level formating...
NAND Low-level formatted...

Superboot-210
Ver: 1.12(20121114)
CPU: S5PV210 1GHz
RAM: 512MB
NAND: 2GB(MLC2) ID:ECD59476
Touch Device: no 1-wire
LCD Type: HDMI1080P30(Manu)

Installing OS 'LINUX'
Installing bootloader...
file: /images/Superboot210.bin: 528 KB(540672 Byte)
Installing bootloader succeed
Installing kernel...
file: /images/Linux/zImage: 4 MB(4810580 Byte)
Installing kernel succeed
Installing yaffs2-image...
file: /images/Linux/rootfs_qtopia_qt4.img: 253 MB(265752384 Byte)
Skip block 0x00000010
Skip block 0x00000011
Skip block 0x00000012
Skip block 0x00000018
Installing yaffs2-image succeed
OS 'LINUX' Installed

不接LCD显示屏，不接HDMI，脱机SD烧录，HDMI1080P30。
烧好滴答声后，关电源，恢复NAND位置，接上HDMI提示无信号。开启电源后接HDMI的显示器是黑屏的。console提示系统进入正常的。

#This line cannot be removed. by FriendlyARM(www.arm9.net)
#USB-Mode=Yes
CheckOneButton=No
Action = Install
OS =Linux

LCD-Mode = No
LCD-Type = HDMI720P60
#LCD-Type = S70

LowFormat = Yes
VerifyNandWrite = No
CheckCRC32=No

StatusType = Beeper | LED

################### Android 4.0.3 ####################
#Android-BootLoader = Superboot210.bin
#Android-Kernel = Android/zImage
#Android-CommandLine = root=/dev/mtdblock4 rootfstype=yaffs2 console=ttySAC0,115200

#init=/linuxrc androidboot.console=ttySAC0 gs=0
#Android-RootFs-InstallImage = Android/rootfs_android.img

################### Android 2.3.1 ####################
#Android-BootLoader = Superboot210.bin
#Android-Kernel = Android2.3.1/zImage
#Android-CommandLine = root=/dev/mtdblock4 rootfstype=yaffs2 console=ttySAC0,115200

#init=/linuxrc androidboot.console=s3c2410_serial0 gs=0
#Android-RootFs-InstallImage = Android2.3.1/rootfs_android.img

################### Linux ####################
Linux-BootLoader = Superboot210.bin
Linux-Kernel = Linux/zImage
Linux-CommandLine = root=/dev/mtdblock4 skipcali=yes rootfstype=yaffs2

console=ttySAC0,115200 init=/linuxrc
Linux-RootFs-InstallImage = Linux/rootfs_qtopia_qt4.img

LCD显示屏和HDMI非全屏同时显示是可以的。独立输出全屏，按论坛里的，“210板如何设置HDMI电视全屏输出”挨步测试还是黑屏的

1) 使用新版 本的 minitools和superboot
2) 注意，开机时，电视需要处于接收HDMI信号状态，如果电视是睡眠的，HDMI不会唤醒
3) 可用Android测试一下看是否有HDMI输出

720P可以，但也是有黑边框，放个720P的视频卡飞了