<6>spca508: registered
<6>usbcore: registered new interface driver spca561
<6>spca561: registered
<6>usbcore: registered new interface driver sq905
<6>sq905: registered
<6>usbcore: registered new interface driver sq905c
<6>sq905c: registered
<6>usbcore: registered new interface driver sunplus
<6>sunplus: registered
<6>usbcore: registered new interface driver stk014
<6>stk014: registered
<6>usbcore: registered new interface driver t613
<6>t613: registered
<6>usbcore: registered new interface driver tv8532
<6>tv8532: registered
<6>usbcore: registered new interface driver vc032x
<6>vc032x: registered
<6>usbcore: registered new interface driver zc3xx
<6>zc3xx: registered
<6>usbcore: registered new interface driver ALi m5602
<6>ALi m5602: registered
<6>usbcore: registered new interface driver STV06xx
<6>STV06xx: registered
<6>gspca_gl860: driver startup - version 0.9d10
<6>usbcore: registered new interface driver gspca_gl860
<6>gspca_gl860: driver registered
<6>usbcore: registered new interface driver uvcvideo
<6>USB Video Class driver (v0.1.0)
<1>initializing s3c2440 camera interface......
<1>s3c2440 camif init done
<1>Loading OV9650 driver.........
<4>SCCB address 0x60, manufacture ID 0xFFFF, expect 0x7FA2
<4>SCCB address 0x60, manufacture ID 0xFFFF, expect 0x7FA2
<3>No OV9650 found!!!
<6>S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
<6>s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
<6>s3c-sdi s3c2440-sdi: powered down.
<6>s3c-sdi s3c2440-sdi: mmc0 - using pio, sw SDIO IRQ
<6>usbcore: registered new interface driver usbhid
<6>usbhid: v2.6:USB HID core driver
<6>Advanced Linux Sound Architecture Driver Version 1.0.21.
<4>No device for DAI UDA134X
<4>No device for DAI s3c24xx-i2s
<6>S3C24XX_UDA134X SoC Audio driver
<6>UDA134X SoC Audio Codec
<6>asoc: UDA134X <-> s3c24xx-i2s mapping ok
<6>ALSA device list:
<6> #0: S3C24XX_UDA134X (UDA134X)
<6>TCP cubic registered
<6>NET: Registered protocol family 17
<6>s3c2410-rtc s3c2410-rtc: setting system clock to 2021-09-05 07:22:01 UTC (163 0826521)
<6>yaffs: dev is 32505859 name is "mtdblock3"
<6>yaffs: passed flags ""
<4>yaffs: Attempting MTD mount on 31.3, "mtdblock3"
<4>yaffs: auto selecting yaffs2
<4>block 526 is bad
<4>block 1025 is bad
<4>block 1362 is bad
<4>block 1435 is bad
<4>block 1546 is bad
<4>yaffs_read_super: isCheckpointed 0
<4>VFS: Mounted root (yaffs filesystem) on device 31:3.
<6>Freeing init memory: 156K
<6>eth0: link down
这是串口打印信息，屏幕是闪屏的
系统已经进去了。
<6>Freeing init memory: 156K
<6>eth0: link down
^C
[root@FriendlyARM /proc]# ls
1 420 buddyinfo ioports partitions
11 5 bus irq self
2 641 cmdline kallsyms slabinfo
209 685 cpu kmsg softirqs
211 688 cpuinfo kpagecount stat
213 692 crypto kpageflags sys
225 695 devices loadavg sysvipc
231 704 diskstats locks timer_list
247 705 driver meminfo tty
254 706 execdomains misc uptime
3 708 fb modules version
301 709 filesystems mounts vmallocinfo
305 715 fs mtd vmstat
309 735 interrupts net yaffs
4 asound iomem pagetypeinfo zoneinfo
[root@FriendlyARM /proc]#
这个是硬件原因还是？ 我是正常按步骤来烧写UBOOT 内核 和文件系统的
