2.4.7 如何通过网络远程控制显示USB 摄像头 求助

我是个超级菜鸟，问的问题可能很幼稚，请原谅。但可能也对其它初学者有帮助。

2.4.7 如何通过网络远程控制显示USB 摄像头
我完全是按手册上写的操作，可是就是ping不通

1.我用板子自带的网线直接将PC机的网口和板子的网口相连，这样对吗？

接上面

2.PC机的IP我设为 192.168.1.120  NETMASK为255.255.255.0
  板子的IP为默认的192.168.1.230
  双方互ping ,哪个也ping不通。怎么做？
3.根据说明书上写的，板子上的LED读数正常。
4.做这个实验和板子或PC机的MAC有关系吗？需要改吗？若是需要怎么改？
我试了好几天都没成功，所以才发到这样麻烦大家，请多多帮忙。
万分感谢。

把板子的串口输出完整的贴出来，从上电开始，否则谁也帮不了你

关掉防火墙试试。我遇到过瑞星防火墙开着PING不通。

一。
主机我设为
ip地址：192.168.1.120
子网掩码：255.255.255.0
默认网关：192.168.1.1

我在超级终端里输入ifconfig，得到开发板的网卡属性是：
ip地址：192.168.1.230
子网掩码：255.255.255.0
默认网关：192.168.1.255

然后再超级终端中输入：
#route add default gw 192.168.1.1
ifconfig eth0 192.168.1.230
DNS没设置

二。
主机我设为
ip地址：192.168.1.120
子网掩码：255.255.255.0
默认网关：192.168.1.230

然后再超级终端中输入：
#route add default gw 192.168.1.120
ifconfig eth0 192.168.1.230
DNS没设置

三，我不设默认网关

试了很多方法都不行，防火强什么的都关了。
我想试验下通过网络采集USB摄相头图像那个，结果还是连ping都ping不通。网页就更上不去了。
但板子的网卡灯是亮了，还有ping的时候主机网口灯也闪。

下面是开机后串口的所有输出信息。

VIVI version 0.1.4 (root@capcross) (gcc version 2.95.3 20010315 (release)) #0.1.                                                                               
4 Fri Sep 12 02:09:10 CST 2008                             
MMU table base address = 0x33DFC000                                 
Succeed memory mapping.                     
DIVN_UPLL0         
MPLLVal [M:7fh,P:2h,S:1h]                       
CLKDIVN:5h         


+---------------------------------------------+                                             
| S3C2440A USB Downloader ver R0.03 2004 Jan  |                                             
+---------------------------------------------+                                             
USB: IN_ENDPOINT:1 OUT_ENDPOINT:3                               
FORMAT: <ADDR(DATA):4>+<SIZE(n+10):4>+<DATA:n>+<CS:2>                                                   
NOTE: Power off/on or press the reset button for 1 sec                                                     
      in order to get a valid USB device address.                                               

NAND device: Manufacture ID: 0xec, Chip ID: 0x76 (Samsung K9D1208V0M)                                                                   
Could not found stored vivi parameters. Use default vivi parameters.                                                                   
Press Return to start the LINUX/Wince now, any other key for vivi                                                               
Copy linux kernel from 0x00050000 to 0x30008000, size = 0x00200000 ... done                                                                         
zImage magic = 0x016f2818                       
Setup linux parameters at 0x30000100                                   
linux command line is: "noinitrd root=/dev/mtdblock2 init=/linuxrc console=ttySA                                                                               
C0" 
MACH_TYPE = 782             
NOW, Booting Linux......                       
Uncompressing Linux.............................................................                                                                               
............................................ done, booting the kernel.                                                                     
Linux version 2.6.13 (root@capcross) (gcc version 3.4.1) #19 Sun Sep 7 23:05:51                                                                             
CST 2008       
CPU: ARM920Tid(wb) [41129200] revision 0 (ARMv4T)                                               
Machine: QQ2440             
ATAG_INITRD is deprecated; please update your bootloader.                                                       
Memory policy: ECC disabled                       
CPU S3C2440A (id 0x32440001)s, associativity 64, 32 byte
BUG: mapping for 0x19000000 at 0xd0000000 overlaps vmalloc space                           
<4>Built 1 zonelistsic = 0x016f281
S3C2440: core 405.000 MHz, memory 101.250 MHz, peripheral 50.625 MHz root=/dev/mtdblock2 init=/linuxrc console=ttySA                   
S3C2410 Clocks, (c) 2004 Simtec Electronics               
linux command line is: "no
CPU0: D VIVT write-back cachet=/linuxrc                 
CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 setsaring subpending status 00000002                                 
CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets....                                                             
Built 1 zonelistsu               
Kernel command line: noinitrd root=/dev/mtdblock2 init=/linuxrc console=ttySAC0                                                                 
.. 
<4>Con
irq: clearing subpending status 00000002 b                                     
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)ble entries: 512                                     
<6>CPU:
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)Hz, peripheral 5                                           
Memory: 64MB = 64MB total             
<6>NET: Re
Memory: 61056KB available (2532K code, 1034K data, 144K init) 
<4>USB Power Control, (c) 2004 Simtec Electronics       
Mount-cache hash table entries: 512   
CPU0: D V       
<4>S3C2440:
CPU: Testing write buffer coherency: ok                     
CPU0: I cache:
NET: Registered protocol family 16
<4>S3C2440: IRQ Supportbyte lines
USB Power Control, (c) 2004 Simtec Ele         
                         
DMA channel 1 at c4800040, irq 34-31 Richard Gooch (rgooch@atnf.cs
DMA channel 2 at c4800080, irq 35                             
In
DMA channel 3 at c48000c0, irq 36 0x192 (order: 3, 32768 bytes) 
NetWinder Floating Point Emulator V0.97 (double precision) Sep  7 2008 23:01:44 Installing.                       
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)       
<6>Initializing Cryptographic API: 61056KB av
devfs: boot_options: 0x1                       
yaffs Sep  7 2008 23:01:44 Instal 
                           
GPIO L3 bus interface for S3C2440, installed                     
<4>buttons initialize
S3C2410 RTC, (c) 2004 Simtec Electronics
<4>qq2440_pwm initializedalized       
s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling 
<4>s3c2410_serial0 at MMIO 0x50000000 (irq = 7
leds initialized               
buttons initialized                 
qq2440_pwm initialized DMA Driver, (c) 2003-
s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2440   
<4>s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a
s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2440                                                         
s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2440 0x50008000 (irq                                       
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize /]# clear100oc/sys/net/                                           
loop: loaded (max 8 devices)
<4>DM9000 ethernet driver
nbd: registered device at major 43                                 
DM9000 ethernet driver V1.26 I/O: c481a300, VID: 90000a46
S3C24X0 fb0:           
<6>Linux video capture interfac
Linux video capture interface: v1.00                               
<6>
ovcamchip: v2.27 for Linux 2.6 : OV camera chip I2C drivertalledc: v2.01:USB HID core driver[k] Download lin       
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2                                             
S3C2410
ide: Assuming 50MHz system bus speed for PIO mered.                                     
)e
NAND_ECC_NONE selected by board driver. This is not recommended !!
<7>initialising set 0 (c0516400, info c057b9e0)size 1024 blocksiz
Scanning device for bad blocks                             
Creating 3 MTD partitions on "NAND 64MiB 3,3V 8-bit": ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MiB 3,3V 8-w
0x00000000-0x00030000 : "bootloader"                                   
0x00050000-0x00250000 : "kernel" registered device at major 43ze
0x00250000-0x03ffc000 : "root"                             
s3c2410-ohci s3c2410-ohci: S3C24X                             
hub 1-0:1.0: 2 ports detecteder 1ns, Twrph0 39ns, Twrph1 9
Initializing USB Mass Storage driver... 4096 byte                           
usbcore: registered new driver usb-storage                                         
USB Mass Storage support registered.<6>s3c2410-ohci s3c2410-ohci: irq 42
usbcore: registered new driver usbhidMiB 3,3V 8-bitters2532K             
drivers/usb/input/hid-core.c: v2.01:USB HID core driver                         
<6>hub 1-0:1.0: USB hub fou
usbcore: registered new driver ov511                                   
drivers/usb/media/ov511.c: v1.64 for Linux 2.5 : ov511 USB Camera Driverommende                                                               

s3c241     
<
mice: PS/2 mouse device common for all miceD core driverumber 1S)stered new drive   
ts: Compaq touchscreen protocol output                                     
s3c2410 TouchScreen successfully loaded110-ohci: irq 42, io mem 0x49000000: Re
i2c /dev entries driver                     
s3c2440-i2c s3c2440-i2c: slave address 0x10usb/media/ov511.c: v1.64 for Linux 2.5 : ov
s3c2440-i2c s3c2440-i2c: bus frequency set to 98 KHz                                                   
s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter 32505858 name is "m                         
s3c2410-sdi s3c2410-sdi: powered down.media/gspca/gspca_core.c: USB SPCA5XX
s3c2410-sdi s3c2410-sdi: initialisation done.                                           
SBC2440 SOUND driver registerver u                       
NET: Registered protocol family 2                 
<6>s3c2410 Tou
s3c2410-sdi s3c2410-sdi: running at 198kHz (requested: 197kHz).             

<6>i2c /dev entries driver                   
s3c2410-sdi s3c2410-sdi: running at 198kHz (requested: 197kHz).: driver dev_driver registered.3XX) of                       
s3c2410-sdi s3c2410-sdi: s3cmci_request: no cardc2440-i2c s3c2440-i2c: clock source c02a9c68ed n
s3c2410-sdi s3c2410-sdi: running at 198kHz (requested: 197kHz).                                                             
s3c2410-sdi s3c2410-sdi: s3cmci_request: no carders c4b80000 (c053cb20, c02aad9c)egistereddia/no
s3c2410-sdi s3c2410-sdi: s3cmci_request: no card                                           
24
s3c2410-sdi s3c2410-sdi: powered down.                                     
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)                     
<4>SBC2440 UDA1341 audio driver initial
TCP established hash table entries: 4096 (order: 3, 32768 bytes)             
<6>NET: Registered protocol family 2: running at
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)                                   
<6>s3c2410-sdi s3c2
TCP: Hash tables configured (established 4096 bind 4096)                                                       
TCP reno registered-sdi: s3cmci_reques
TCP bic registered                 
yaffs: Attempting MTD mount on 31.2, "mtdblock2"
          TX packets:0 errors:0             
VFS: Mounted root (yaffs filesystem).<6>s3c2410-sdi s3c2410-sdi: running a
Mounted devfs on /dev97kHz).             
Freeing init memory: 144K                       
mini2440_backlight: module license 'unspecified' taints kernel.                             
<3>s3c2410-sdi s3c2410-sdi: s3cm
backlight initialized410-sdi s3c2410-sdi:
[08/Sep/2008:05:24:49 +0000] boa: server version Boa/0.94.13                         
<3>s3c2410-sdi s3c2410-sdi: s3cmc
[08/Sep/2008:05:24:49 +0000] boa: server built Feb 28 2004 at 21:47:23.                                                                     
[08/Sep/2008:05:24:49 +0000] boa: starting server pi                                                 
    Title: 上海滩                 
    Artist: 叶丽仪                 
      Year: 2000         
<6>s3
    Genre: Goa0-sdi: powered



iShow - A Picture Viewer by FriendlyARM.ed55205] irq 42,                       
/media/note.jpgroute cache has
240 x 320tries: 10
7316 frames decoded (0:03:11.1), +0.0 dB peak amplitude, 6 clipped samples                                                                         





Please press Enter to activate this console.sh table entries: 4096 (order: 3, 32768 byte
[root@FriendlyARM /]# clear0 overruns:0 carrier:0in/fr




[root@FriendlyARM /]#                   
          col           
VFS: Mounted
4 Fri Sep 12 02:09:10 CST 2008                 

lo 
<6>y
MMU table base address = 0x33DFC000ock2":12:59 +0000] boa: server buil
Succeed memory mapping.                     
DIVN_UPLL0         
MPLLVal [M:7fh,P:2h,S:1h]         
<4>yaffs: Att
CLKDIVN:5h mount on


+---------------------------------------------+                 
[08/Sep/2008:05:12:5       
| S3C2440A USB Downloader ver R0.03 2004 Jan  |tem).rt 80    TX packets:0 errors:0 dropped:0 
+---------------------------------------------+                             
<6>Mounted devfs
USB: IN_ENDPOINT:1 OUT_ENDPOINT:3enable_irq(51) u               

FORMAT: <ADDR(DATA):4>+<SIZE(n+10):4>+<DATA:n>+<CS:2> 
TOC {col f         
d
<7>selected clock c02de4a8
NOTE: Power off/on or press the reset button for 1 sec                                                     
Uncompressing Linux.............................................................                                           
console    input      mixer     
............................................ done, booting the kernel.
          collisions:0 txqueuelen:1000255  Mask:255.255.255.0dateded
Linux version 2.6.13 (root@capcross) (gcc version 3.4.1) #19 Sun Sep 7 23:05:51    RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)    vcc                           
CST 2008       
CPU: ARM920Tid(wb) [41129200] revision 0 (ARMv4T)a300    nbd        rd          tty        v 
Machine: QQ2440             
ATAG_INITRD is deprecated; please update your bootloader.    Link encap:Local Loopback                           
Memory policy: ECC disabled, Data cache writeback1  Ma.                                 

     
CPU S3C2440A (id 0x32440001)es:0 (0.0 B)deo07316 frames
BUG: mapping for 0x19000000 at 0xd0000000 overlaps vmalloc space                                               

           
CPU0: D VIVT write-back cache No such                   
CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets:255.255.255.0dlyARM /dev]# dmesg                                 
CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets version 2.6.13                     
          UP BROADCAST RUNNI
Built 1 zonelists1500  Metric:1 
Kernel command line: noinitrd root=/dev/mtdblock2 init=/linuxrc console=ttySAC0       
<4>CPU0     

[root@FriendlyARM /dev]# clearute: SIOC[ADD|DEL]RT: Fi
irq: clearing subpending status 00000002             
<4>C   





PID hash table entries: 512 (order: 9, 8192 bytes)                                   
[root@Friend
timer tcon=00000000, tcnt a4ca, tcfg 00000200,00                                             
GPIO L3 bus interface for S3C2440, installed0200,00000000, usec 00001e57004 Simtec Elect
S3C2410 RTC, (c) 2004 Simtec Electronics                                       
s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling60 errors                             
<4>Console
leds initializedvice 80x30q 33 
buttons initialized                 
qq2440_pwm initializede4a8 (pclk) quot 26, c
s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2440   
 

<4>DMA channel 2 at c4800080, ir           
s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2440384 (order: 4, 65536 bytes)0c0, irq 36                   
s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2440] Print the TOC struc                     
<4>NetWinder
io scheduler noop registerede-cache hash table entries:
io scheduler anticipatory registeredlash to HOST through U             
io scheduler deadline registered                               
io scheduler cfq registered04-01-31                 
DM9000 ethernet driver V1.26 I/O: c481a300, VID: 90000a46 
<4>buttons init             
<5>SCSI subsystem init
Linux video capture interface: v1.00                                   
ovcamchip: v2.27 for Linux 2.6 : OV camera chip I2C driverl0 at MMIO 0x50000000 (irq = 70) is a                   
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2S3C2410 DMA Driver, (c) 2003-2004 Simtec Electron     
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx                       
<6>devfs: 2004-01-31 Richard Gooch (rgooch@atnf.cs
S3C24XX NAND Driver, (c) 2004 Simtec Electronicsrs:0                                           
s3c2440-nand: mapped registers at c4880000               
<4>RAMDIS       
     
Scanning device for bad blocks                   
<4>DM9000
Creating 3 MTD partitions on "NAND 64MiB 3,3V 8-bit":                           
<6>S3C24X0 fb0: s3c2410
0x00000000-0x00030000 : "bootloader"e                                 
0x00050000-0x00250000 : "kernel"ux video capture interface: v1.0
0x00250000-0x03ffc000 : "root"                         
<4
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI         

<6>s3c2440-nand: mapped reg
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1 scheduler noop registered2554 (276                                   
drivers/usb/input/hid-core.c: v2.01:USB HID core driver                                   
<7>i2c-core: drive
usbcore: registered new driver ov511                         
<5>0x000
drivers/usb/media/ov511.c: v1.64 for Linux 2.5 : ov511 USB Camera Driverform Multi-Platform E-IDE driver Revision: 7.00alpha2250000 : "kernel" 
usbcore: registered new driver gspca                                   
drivers/usb/media/gspca/gspca_core.c: gspca dri                                           
i2c /dev entries driver                     
s3c2440-i2c s3c2440-i2c: slave address 0x10 (c) 20                             
<7>re
s3c2440-i2c s3c2440-i2c: bus frequency set to 98 KHz
<6>s3c2440-nand: timing: Tacls 9ns, Twrph0 39ns, Tw
s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter                 
<6>Initializing USB Mass St
s3c2410-sdi s3c2410-sdi: powered down.                       
<7>s3c2440-na
s3c2410-sdi s3c2410-sdi: initialisation done.     
<6>usbcore: registered new dr       
SBC2440 SOUND driver registeralising set 0 (c0516400, info
s3c2410-sdi s3c2410-sdi: running at 0kHz (requested: 0kHz).                     
<6>USB Mass Storage support regis 
SBC2440 SOUND driver probe! 
                     
SBC2440 UDA1341 audio d                     
<6>Scanning device for bad blocksUSB: IN_E
s3c2410-sdi s3c2410-sdi: s3cmci_request: no card                                       
<6>s3c
s3c2410-sdi s3c2410-sdi: s3cmci_request: no cardpca driver 00.60.00 registere                 
s3c2410-sdi s3c2410-sdi: s3cmci_request: no card               
<6>s3c2410-ohci s3c2410-ohci: n
s3c2410-sdi s3c2410-sdi: s3cmci_request: no ca                                           
<6>hub 1-0:1.0: 2 ports detected6>s3c2410 TouchScreen s
TCP established hash table entries: 4096 (order: 3, 32768 bytes)       
<6>Initializing USB Mass Storage driver...           
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)nux..                               
<6>usbcore: regist
TCP: Hash tables configured (established 4096 bind 4096)                                             
<6>drive
TCP reno registered: v1.64 for Linux 2
TCP bic registeredra Drivers3c2440-i
NET: Registered protocol family 10T  MTU:1500  Metric:1is depreca
NET: Registered protocol family 17                                 
yaffs: dev is 32505858 name is "mtdblock2"                                   
<6>d
yaffs: Attempting MTD mount on 31.2,                                 
[08/Sep/2008:05:30:07 +0000] boa: server version Boa/0.94.13                           

<6>s3c2410 TouchScreen success
[08/Sep/2008:05:30:07 +0000] boa: server built Feb 28 2004 at 21:47:23.                               
<6>s3c2410-sdi s               
<6>i2
[08/Sep/2008:05:30:07 +0000] boa: starting server pid=271, port 80                   
<7>i2c-core: driver dev_driver registered. 

enable_irq(51) unbalanced from c0173b504>SBC2440 SOUND driver probe         
MPEG Audio Decoder 0.15.0 (beta) - Copyright (C) 2000-2003 Robert Leslie et al.r initializedec Electronics                                                   
    Title: 上海滩               


iShow - A Picture Viewer by FriendlyARM.
/media/note.jpg
240 x 320

请kasim帮忙解决下这个网络的问题吧，我从买板子到现在一周多了，一直调也没好用。难道我PC机那边有问题，需要什么特殊的设置吗？
我是根据上面的那种方法设置的。

你的PC主机上有别的网卡也配了192.168.1.*这样的地址吗？

没有，我就一个网卡，有两个虚拟的，操作时我还把它们关闭了，相当于就这一个网卡。

再贴一下板子上运行dmesg以及ifconfig -a 和 cat /proc/net/dev 的输出吧，如果你是用超级终端的，记得用菜单上的“传输”－>"获取文字"， 把串口输出保存到文件里，否则又是一堆垃圾

这是按您说的所有信息。还有PC机上有没有需要什么特别注意的地方也说一下吧，再次感谢版主。

dmesg
<5>Linux version 2.6.13 (root@capcross) (gcc version 3.4.1) #19 Sun Sep 7 23:05:51 CST 2008
<4>CPU: ARM920Tid(wb) [41129200] revision 0 (ARMv4T)
<4>Machine: QQ2440
<7>Converting old-style param struct to taglist
<4>ATAG_INITRD is deprecated; please update your bootloader.
<4>Memory policy: ECC disabled, Data cache writeback
<4>CPU S3C2440A (id 0x32440001)
<4>BUG: mapping for 0x19000000 at 0xd0000000 overlaps vmalloc space
<4>S3C2440: core 405.000 MHz, memory 101.250 MHz, peripheral 50.625 MHz
<6>S3C2410 Clocks, (c) 2004 Simtec Electronics
<7>On node 0 totalpages: 16384
<7>  DMA zone: 16384 pages, LIFO batch:7
<7>  Normal zone: 0 pages, LIFO batch:1
<7>  HighMem zone: 0 pages, LIFO batch:1
<4>CPU0: D VIVT write-back cache
<4>CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
<4>CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
<4>Built 1 zonelists
<5>Kernel command line: noinitrd root=/dev/mtdblock2 init=/linuxrc console=ttySAC0
<4>irq: clearing subpending status 00000002
<4>PID hash table entries: 512 (order: 9, 8192 bytes)
<4>timer tcon=00000000, tcnt a4ca, tcfg 00000200,00000000, usec 00001e57
<4>Console: colour dummy device 80x30
<7>selected clock c02de4a8 (pclk) quot 26, calc 117187
<4>Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
<4>Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
<6>Memory: 64MB = 64MB total
<5>Memory: 61056KB available (2532K code, 1034K data, 144K init)
<7>Calibrating delay loop... 202.34 BogoMIPS (lpj=505856)
<4>Mount-cache hash table entries: 512
<6>CPU: Testing write buffer coherency: ok
<6>NET: Registered protocol family 16
<4>USB Power Control, (c) 2004 Simtec Electronics
<4>S3C2440: Initialising architecture
<4>S3C2440: IRQ Support
<4>S3C2440: Clock Support, UPLL 48.000 MHz
<5>SCSI subsystem initialized
<6>usbcore: registered new driver hub
<4>S3C2410 DMA Driver, (c) 2003-2004 Simtec Electronics
<4>DMA channel 0 at c4800000, irq 33
<4>DMA channel 1 at c4800040, irq 34
<4>DMA channel 2 at c4800080, irq 35
<4>DMA channel 3 at c48000c0, irq 36
<4>NetWinder Floating Point Emulator V0.97 (double precision)
<6>devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
<6>devfs: boot_options: 0x1
<4>yaffs Sep  7 2008 23:01:44 Installing.
<6>Initializing Cryptographic API
<4>Console: switching to colour frame buffer device 30x20
<6>S3C24X0 fb0: s3c2410fb frame buffer device initialize done
<4>GPIO L3 bus interface for S3C2440, installed
<4>S3C2410 RTC, (c) 2004 Simtec Electronics
<6>s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling
<4>leds initialized
<4>buttons initialized
<4>qq2440_pwm initialized
<4>s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2440
<4>s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2440
<4>s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2440
<6>io scheduler noop registered
<6>io scheduler anticipatory registered
<6>io scheduler deadline registered
<6>io scheduler cfq registered
<4>RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
<6>loop: loaded (max 8 devices)
<6>nbd: registered device at major 43
<4>DM9000 ethernet driver V1.26 I/O: c481a300, VID: 90000a46
<6>Linux video capture interface: v1.00
<6>ovcamchip: v2.27 for Linux 2.6 : OV camera chip I2C driver
<7>i2c-core: driver ovcamchip registered.
<6>Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
<6>ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
<4>S3C24XX NAND Driver, (c) 2004 Simtec Electronics
<7>s3c2410_nand_probe(c02ab29c)
<6>s3c2440-nand: mapped registers at c4880000
<7>result 1 from 101250, 0
<7>result 4 from 101250, 30
<7>result 1 from 101250, 0
<6>s3c2440-nand: timing: Tacls 9ns, Twrph0 39ns, Twrph1 9ns
<7>s3c2440-nand: NF_CONF is 0x300
<7>initialising set 0 (c0516400, info c057b9e0)
<6>NAND device: Manufacturer ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MiB 3,3V 8-bit)
<4>NAND_ECC_NONE selected by board driver. This is not recommended !!
<6>Scanning device for bad blocks
<5>Creating 3 MTD partitions on "NAND 64MiB 3,3V 8-bit":
<5>0x00000000-0x00030000 : "bootloader"
<5>0x00050000-0x00250000 : "kernel"
<5>0x00250000-0x03ffc000 : "root"
<7>initialised ok
<6>s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
<6>s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
<6>s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
<6>hub 1-0:1.0: USB hub found
<6>hub 1-0:1.0: 2 ports detected
<6>Initializing USB Mass Storage driver...
<6>usbcore: registered new driver usb-storage
<6>USB Mass Storage support registered.
<6>usbcore: registered new driver usbhid
<6>drivers/usb/input/hid-core.c: v2.01:USB HID core driver
<6>usbcore: registered new driver ov511
<6>drivers/usb/media/ov511.c: v1.64 for Linux 2.5 : ov511 USB Camera Driver
<6>usbcore: registered new driver gspca
<6>drivers/usb/media/gspca/gspca_core.c: gspca driver 00.60.00 registered
<6>mice: PS/2 mouse device common for all mice
<6>ts: Compaq touchscreen protocol output
<7>Entering s3c2410ts_init
<7>got and enabled clock
<6>s3c2410 TouchScreen successfully loaded
<6>i2c /dev entries driver
<7>i2c-core: driver dev_driver registered.
<7>s3c2440-i2c s3c2440-i2c: clock source c02a9c68
<7>s3c2440-i2c s3c2440-i2c: registers c4b80000 (c053ce20, c02aad9c)
<6>s3c2440-i2c s3c2440-i2c: slave address 0x10
<7>s3c2440-i2c s3c2440-i2c: pdata c02f9000, freq 100000 0..400000
<6>s3c2440-i2c s3c2440-i2c: bus frequency set to 98 KHz
<7>s3c2440-i2c s3c2440-i2c: S3C2410_IICCON=0xe0
<7>s3c2440-i2c s3c2440-i2c: S3C2440_IICLC=00000005
<7>s3c2440-i2c s3c2440-i2c: irq resource c02aadb8 (43)
<7>i2c_adapter i2c-0: Registered as minor 0
<7>i2c_adapter i2c-0: registered as adapter #0
<6>s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
<6>s3c2410-sdi s3c2410-sdi: powered down.
<6>s3c2410-sdi s3c2410-sdi: initialisation done.
<4>SBC2440 SOUND driver register
<6>s3c2410-sdi s3c2410-sdi: running at 0kHz (requested: 0kHz).
<4>SBC2440 SOUND driver probe!
<4>SBC2440 UDA1341 audio driver initialized
<6>NET: Registered protocol family 2
<6>s3c2410-sdi s3c2410-sdi: running at 198kHz (requested: 197kHz).
<6>s3c2410-sdi s3c2410-sdi: running at 198kHz (requested: 197kHz).
<3>s3c2410-sdi s3c2410-sdi: s3cmci_request: no card
<6>s3c2410-sdi s3c2410-sdi: running at 198kHz (requested: 197kHz).
<3>s3c2410-sdi s3c2410-sdi: s3cmci_request: no card
<3>s3c2410-sdi s3c2410-sdi: s3cmci_request: no card
<3>s3c2410-sdi s3c2410-sdi: s3cmci_request: no card
<3>s3c2410-sdi s3c2410-sdi: s3cmci_request: no card
<3>s3c2410-sdi s3c2410-sdi: s3cmci_request: no card
<3>s3c2410-sdi s3c2410-sdi: s3cmci_request: no card
<6>s3c2410-sdi s3c2410-sdi: powered down.
<4>IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
<4>TCP established hash table entries: 4096 (order: 3, 32768 bytes)
<4>TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
<6>TCP: Hash tables configured (established 4096 bind 4096)
<6>TCP reno registered
<6>TCP bic registered
<6>NET: Registered protocol family 1
<6>NET: Registered protocol family 17
<6>yaffs: dev is 32505858 name is "mtdblock2"
<4>yaffs: Attempting MTD mount on 31.2, "mtdblock2"
<4>VFS: Mounted root (yaffs filesystem).
<6>Mounted devfs on /dev
<6>Freeing init memory: 144K
<7>selected clock c02de4a8 (pclk) quot 26, calc 117187
<7>selected clock c02de4a8 (pclk) quot 26, calc 117187
<7>selected clock c02de4a8 (pclk) quot 26, calc 117187
<7>selected clock c02de4a8 (pclk) quot 26, calc 117187
<7>selected clock c02de4a8 (pclk) quot 26, calc 117187
<4>mini2440_backlight: module license 'unspecified' taints kernel.
<4>backlight initialized
<4>enable_irq(51) unbalanced from c0173b50
<7>selected clock c02de4a8 (pclk) quot 26, calc 117187

[root@FriendlyARM /]# ifconfig -a
dummy0    Link encap:Ethernet  HWaddr CA:35:D6:85:74:3C 
          BROADCAST NOARP  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

eth0      Link encap:Ethernet  HWaddr 00:13:F6:6C:87:89 
          inet addr:192.168.1.230  Bcast:192.168.1.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:165 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:51 Base address:0xa300

lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:162 errors:0 dropped:0 overruns:0 frame:0
          TX packets:162 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:18144 (17.7 KiB)  TX bytes:18144 (17.7 KiB)


[root@FriendlyARM /]# cat /proc/net/dev
Inter-|  Receive                                                |  Transmit
face |bytes    packets errs drop fifo frame compressed multicast|bytes    packets errs drop fifo colls carrier compressed
    lo:  18144    162    0    0    0    0          0        0    18144    162    0    0    0    0      0          0
dummy0:      0      0    0    0    0    0          0        0        0      0    0    0    0    0      0          0
  eth0:      0      0    0    0    0    0          0        0        0    165    0    0    0    0      0          0
[root@FriendlyARM /]#